Signal Encoding Techniques

Presentation on theme: "Signal Encoding Techniques"— Presentation transcript:

1 Signal Encoding Techniques
Chapter 6

2

3 Reasons for Choosing Encoding Techniques
Digital data, digital signal Equipment less complex and expensive than digital-to-analog modulation equipment Analog data, digital signal Permits use of modern digital transmission and switching equipment

4 Reasons for Choosing Encoding Techniques
Digital data, analog signal Some transmission media will only propagate analog signals E.g., optical fiber and unguided media Analog data, analog signal Analog data in electrical form can be transmitted easily and cheaply Done with voice transmission over voice-grade lines

5 Signal Encoding Criteria
What determines how successful a receiver will be in interpreting an incoming signal? Signal-to-noise ratio Data rate Bandwidth An increase in data rate increases bit error rate An increase in SNR decreases bit error rate An increase in bandwidth allows an increase in data rate

6

7 Factors Used to Compare Encoding Schemes
Signal spectrum With lack of high-frequency components, less bandwidth required With no dc component, ac coupling via transformer possible Transfer function of a channel is worse near band edges Clocking Ease of determining beginning and end of each bit position

8 Factors Used to Compare Encoding Schemes
Signal interference and noise immunity Performance in the presence of noise Cost and complexity The higher the signal rate to achieve a given data rate, the greater the cost

9 Basic Encoding Techniques
Digital data to analog signal Amplitude-shift keying (ASK) Amplitude difference of carrier frequency Frequency-shift keying (FSK) Frequency difference near carrier frequency Phase-shift keying (PSK) Phase of carrier signal shifted

10 Basic Encoding Techniques

11 Amplitude-Shift Keying
One binary digit represented by presence of carrier, at constant amplitude Other binary digit represented by absence of carrier where the carrier signal is Acos(2πfct)

12 Amplitude-Shift Keying
Susceptible to sudden gain changes Inefficient modulation technique On voice-grade lines, used up to 1200 bps Used to transmit digital data over optical fiber

13 Binary Frequency-Shift Keying (BFSK)
Two binary digits represented by two different frequencies near the carrier frequency where f1 and f2 are offset from carrier frequency fc by equal but opposite amounts

14 Binary Frequency-Shift Keying (BFSK)
Less susceptible to error than ASK On voice-grade lines, used up to 1200bps Used for high-frequency (3 to 30 MHz) radio transmission Can be used at higher frequencies on LANs that use coaxial cable

15

16 Multiple Frequency-Shift Keying (MFSK)
More than two frequencies are used More bandwidth efficient but more susceptible to error f i = f c + (2i – 1 – M)f d f c = the carrier frequency f d = the difference frequency M = number of different signal elements = 2 L L = number of bits per signal element

17 Multiple Frequency-Shift Keying (MFSK)
To match data rate of input bit stream, each output signal element is held for: Ts=LT seconds where T is the bit period (data rate = 1/T) So, one signal element encodes L bits

18 Multiple Frequency-Shift Keying (MFSK)
Total bandwidth required 2Mfd Minimum frequency separation required 2fd=1/Ts Therefore, modulator requires a bandwidth of Wd=2L/LT=M/Ts

19 Multiple Frequency-Shift Keying (MFSK)

20 Phase-Shift Keying (PSK)
Two-level PSK (BPSK) Uses two phases to represent binary digits

21 Phase-Shift Keying (PSK)
Differential PSK (DPSK) Phase shift with reference to previous bit Binary 0 – signal burst of same phase as previous signal burst Binary 1 – signal burst of opposite phase to previous signal burst

22

23 Phase-Shift Keying (PSK)
Four-level PSK (QPSK) Each element represents more than one bit

24

25 Phase-Shift Keying (PSK)
Multilevel PSK Using multiple phase angles with each angle having more than one amplitude, multiple signals elements can be achieved D = modulation rate, baud R = data rate, bps M = number of different signal elements = 2L L = number of bits per signal element

26

27 Performance Bandwidth of modulated signal (BT) ASK, PSK BT=(1+r)R
FSK BT=2DF+(1+r)R R = bit rate 0 < r < 1; related to how signal is filtered DF = f2-fc=fc-f1

28 Performance Bandwidth of modulated signal (BT) MPSK MFSK
L = number of bits encoded per signal element M = number of different signal elements

29

30

31

32 Quadrature Amplitude Modulation
QAM is a combination of ASK and PSK Two different signals sent simultaneously on the same carrier frequency

33 Quadrature Amplitude Modulation

34 Reasons for Analog Modulation
Modulation of digital signals When only analog transmission facilities are available, digital to analog conversion required Modulation of analog signals A higher frequency may be needed for effective transmission Modulation permits frequency division multiplexing

35 Basic Encoding Techniques
Analog data to analog signal Amplitude modulation (AM) Angle modulation Frequency modulation (FM) Phase modulation (PM)

36 Amplitude Modulation Amplitude Modulation
cos2fct = carrier x(t) = input signal na = modulation index Ratio of amplitude of input signal to carrier a.k.a double sideband transmitted carrier (DSBTC)

37 Spectrum of AM signal

38 Amplitude Modulation Transmitted power
Pt = total transmitted power in s(t) Pc = transmitted power in carrier

39 Single Sideband (SSB) Variant of AM is single sideband (SSB)
Sends only one sideband Eliminates other sideband and carrier Advantages Only half the bandwidth is required Less power is required Disadvantages Suppressed carrier can’t be used for synchronization purposes

40 Angle Modulation Angle modulation Phase modulation
Phase is proportional to modulating signal np = phase modulation index

41 Angle Modulation Frequency modulation
Derivative of the phase is proportional to modulating signal nf = frequency modulation index

42 Angle Modulation Compared to AM, FM and PM result in a signal whose bandwidth: is also centered at fc but has a magnitude that is much different Angle modulation includes cos( (t)) which produces a wide range of frequencies Thus, FM and PM require greater bandwidth than AM

43 Angle Modulation Carson’s rule where The formula for FM becomes

44 Basic Encoding Techniques
Analog data to digital signal Pulse code modulation (PCM) Delta modulation (DM)

45 Analog Data to Digital Signal
Once analog data have been converted to digital signals, the digital data: can be transmitted using NRZ-L can be encoded as a digital signal using a code other than NRZ-L can be converted to an analog signal, using previously discussed techniques

46

47 Pulse Code Modulation Based on the sampling theorem
Each analog sample is assigned a binary code Analog samples are referred to as pulse amplitude modulation (PAM) samples The digital signal consists of block of n bits, where each n-bit number is the amplitude of a PCM pulse

48 Pulse Code Modulation

49 Pulse Code Modulation By quantizing the PAM pulse, original signal is only approximated Leads to quantizing noise Signal-to-noise ratio for quantizing noise Thus, each additional bit increases SNR by 6 dB, or a factor of 4

50

51

52 Delta Modulation Analog input is approximated by staircase function
Moves up or down by one quantization level () at each sampling interval The bit stream approximates derivative of analog signal (rather than amplitude) 1 is generated if function goes up 0 otherwise

53 Delta Modulation

54

55 Delta Modulation Two important parameters
Size of step assigned to each binary digit () Sampling rate Accuracy improved by increasing sampling rate However, this increases the data rate Advantage of DM over PCM is the simplicity of its implementation

56 Reasons for Growth of Digital Techniques
Growth in popularity of digital techniques for sending analog data Repeaters are used instead of amplifiers No additive noise TDM is used instead of FDM No intermodulation noise Conversion to digital signaling allows use of more efficient digital switching techniques

57

58