Download presentation
1
Chapter 9: BJT and FET Frequency Response
2
General Frequency Considerations
The frequency response of an amplifier refers to the frequency range in which the amplifier will operate with negligible effects from capacitors and device internal capacitance. This range of frequencies can be called the mid-range. At frequencies above and below the midrange, capacitance and any inductance will affect the gain of the amplifier. At low frequencies the coupling and bypass capacitors lower the gain. At high frequencies stray capacitances associated with the active device lower the gain. Also, cascading amplifiers limits the gain at high and low frequencies. 2
3
Bode Plot A Bode plot indicates the frequency response of an amplifier. The horizontal scale indicates the frequency (in Hz) and the vertical scale indicates the gain (in dB). 3
4
Cutoff Frequencies The mid-range frequency range of an amplifier is called the bandwidth of the amplifier. The bandwidth is defined by the lower and upper cutoff frequencies. Cutoff – any frequency at which the gain has dropped by 3 dB. 4
5
BJT Amplifier Low-Frequency Response
At low frequencies, coupling capacitor (CS, CC) and bypass capacitor (CE) reactances affect the circuit impedances. 5
6
Coupling Capacitor (CS)
The cutoff frequency due to CS can be calculated by where 6
7
Coupling Capacitor (CC)
The cutoff frequency due to CC can be calculated with where 7
8
Bypass Capacitor (CE) The cutoff frequency due to CE can be calculated with where and 8
9
BJT Amplifier Low-Frequency Response
The Bode plot indicates that each capacitor may have a different cutoff frequency. It is the device that has the highest lower cutoff frequency (fL) that dominates the overall frequency response of the amplifier. 9
10
Roll-Off of Gain in the Bode Plot
The Bode plot not only indicates the cutoff frequencies of the various capacitors it also indicates the amount of attenuation (loss in gain) at these frequencies. The amount of attenuation is sometimes referred to as roll-off. The roll-off is described as dB loss-per-octave or dB loss-per-decade. 10
11
Roll-off Rate (-dB/Decade)
-dB/decade refers to the attenuation for every 10-fold change in frequency. For attenuations at the low-frequency end, it refers to the loss in gain from the lower cutoff frequency to a frequency that is one-tenth the cutoff value. In this example: fLS = 9kHz gain is 0dB fLS/10 = .9kHz gain is –20dB Thus the roll-off is 20dB/decade The gain decreases by –20dB/decade 11
12
Roll-Off Rate (–dB/Octave)
-dB/octave refers to the attenuation for every 2-fold change in frequency. For attenuations at the low-frequency end, it refers to the loss in gain from the lower cutoff frequency to a frequency one-half the cutoff value. In this example: fLS = 9kHz gain is 0dB fLS / 2 = 4.5kHz gain is –6dB Therefore the roll-off is 6dB/octave. This is a little difficult to see on this graph because the horizontal scale is a logarithmic scale. 12
13
FET Amplifier Low-Frequency Response
At low frequencies, coupling capacitor (CG, CC) and bypass capacitor (CS) reactances affect the circuit impedances. 13
14
Coupling Capacitor (CG)
The cutoff frequency due to CG can be calculated with where 14
15
Coupling Capacitor (CC)
The cutoff frequency due to CC can be calculated with where 15
16
Bypass Capacitor (CS) The cutoff frequency due to CS can be calculated with where 16
17
FET Amplifier Low-Frequency Response
The Bode plot indicates that each capacitor may have a different cutoff frequency. The capacitor that has the highest lower cutoff frequency (fL) is closest to the actual cutoff frequency of the amplifier. 17
18
Miller Capacitance Any p-n junction can develop capacitance. In a BJT amplifier, this capacitance becomes noticeable across: The base-collector junction at high frequencies in common-emitter BJT amplifier configurations The gate-drain junction at high frequencies in common-source FET amplifier configurations. These capacitances are represented as separate input and output capacitances, called the Miller Capacitances. 18
19
Miller Input Capacitance (CMi)
Note that the amount of Miller capacitance is dependent on inter-electrode capacitance from input to output (Cf) and the gain (Av). 19
20
Miller Output Capacitance (CMo)
If the gain (Av) is considerably greater than 1, then 20
21
BJT Amplifier High-Frequency Response
Capacitances that affect the high-frequency response are Junction capacitances Cbe, Cbc, Cce Wiring capacitances Cwi, Cwo Coupling capacitors CS, CC Bypass capacitor CE 21
22
Input Network (fHi) High-Frequency Cutoff
where and 22
23
Output Network (fHo) High-Frequency Cutoff
where and 23
24
hfe (or ) Variation The hfe parameter (or ) of a transistor varies with frequency 24
25
BJT Amplifier Frequency Response
Note the highest lower cutoff frequency (fL) and the lowest upper cutoff frequency (fH) are closest to the actual response of the amplifier. 25
26
FET Amplifier High-Frequency Response
Capacitances that affect the high-frequency response are Junction capacitances Cgs, Cgd, Cds Wiring capacitances Cwi, Cwo Coupling capacitors CG, CC Bypass capacitor CS 26
27
Input Network (fHi) High-Frequency Cutoff
27
28
Output Network (fHo) High-Frequency Cutoff
28
29
Multistage Frequency Effects
Each stage will have its own frequency response, but the output of one stage will be affected by capacitances in the subsequent stage. This is especially so when determining the high frequency response. For example, the output capacitance (Co) will be affected by the input Miller Capacitance (CMi) of the next stage. 29
30
Multistage Amplifier Frequency Response
Once the cutoff frequencies have been determined for each stage (taking into account the shared capacitances), they can be plotted. Note the highest lower cutoff frequency (fL) and the lowest upper cutoff frequency (fH) are closest to the actual response of the amplifier. 30
31
Square Wave Testing In order to determine the frequency response of an amplifier by experimentation, you must apply a wide range of frequencies to the amplifier. One way to accomplish this is to apply a square wave. A square wave consists of multiple frequencies (by Fourier analysis: it consists of odd harmonics). 31
32
Square Wave Response Waveforms
If the output of the amplifier is not a perfect square wave then the amplifier is ‘cutting’ off certain frequency components of the square wave. 32
Similar presentations
© 2023 SlidePlayer.com Inc.
All rights reserved.