Gursharan Singh Tatla 21-Nov-20101www.eazynotes.com.

Presentation on theme: "Gursharan Singh Tatla 21-Nov-20101www.eazynotes.com."— Presentation transcript:

1 Gursharan Singh Tatla professorgstatla@gmail.com 21-Nov-20101www.eazynotes.com

2 Instruction Set of 8086 An instruction is a binary pattern designed inside a microprocessor to perform a specific function. The entire group of instructions that a microprocessor supports is called Instruction Set. 8086 has more than 20,000 instructions. 21-Nov-20102www.eazynotes.com

3 Classification of Instruction Set Data Transfer Instructions Arithmetic Instructions Bit Manipulation Instructions Program Execution Transfer Instructions String Instructions Processor Control Instructions 21-Nov-20103www.eazynotes.com

4 Data Transfer Instructions These instructions are used to transfer data from source to destination. The operand can be a constant, memory location, register or I/O port address. 21-Nov-20104www.eazynotes.com

5 Data Transfer Instructions MOV Des, Src: Src operand can be register, memory location or immediate operand. Des can be register or memory operand. Both Src and Des cannot be memory location at the same time. E.g.: MOV CX, 037A H MOV AL, BL MOV BX, [0301 H] 21-Nov-20105www.eazynotes.com

6 Data Transfer Instructions PUSH Operand: It pushes the operand into top of stack. E.g.: PUSH BX POP Des: It pops the operand from top of stack to Des. Des can be a general purpose register, segment register (except CS) or memory location. E.g.: POP AX 21-Nov-20106www.eazynotes.com

7 Data Transfer Instructions XCHG Des, Src: This instruction exchanges Src with Des. It cannot exchange two memory locations directly. E.g.: XCHG DX, AX 21-Nov-20107www.eazynotes.com

8 Data Transfer Instructions IN Accumulator, Port Address: It transfers the operand from specified port to accumulator register. E.g.: IN AX, 0028 H OUT Port Address, Accumulator: It transfers the operand from accumulator to specified port. E.g.: OUT 0028 H, AX 21-Nov-20108www.eazynotes.com

9 Data Transfer Instructions LEA Register, Src: It loads a 16-bit register with the offset address of the data specified by the Src. E.g.: LEA BX, [DI] This instruction loads the contents of DI (offset) into the BX register. 21-Nov-20109www.eazynotes.com

10 Data Transfer Instructions LDS Des, Src: It loads 32-bit pointer from memory source to destination register and DS. The offset is placed in the destination register and the segment is placed in DS. To use this instruction the word at the lower memory address must contain the offset and the word at the higher address must contain the segment. E.g.: LDS BX, [0301 H] 21-Nov-201010www.eazynotes.com

11 Data Transfer Instructions LES Des, Src: It loads 32-bit pointer from memory source to destination register and ES. The offset is placed in the destination register and the segment is placed in ES. This instruction is very similar to LDS except that it initializes ES instead of DS. E.g.: LES BX, [0301 H] 21-Nov-201011www.eazynotes.com

12 Data Transfer Instructions LAHF: It copies the lower byte of flag register to AH. SAHF: It copies the contents of AH to lower byte of flag register. PUSHF: Pushes flag register to top of stack. POPF: Pops the stack top to flag register. 21-Nov-201012www.eazynotes.com

13 Arithmetic Instructions ADD Des, Src: It adds a byte to byte or a word to word. It effects AF, CF, OF, PF, SF, ZF flags. E.g.: ADD AL, 74H ADD DX, AX ADD AX, [BX] 21-Nov-201013www.eazynotes.com

14 Arithmetic Instructions ADC Des, Src: It adds the two operands with CF. It effects AF, CF, OF, PF, SF, ZF flags. E.g.: ADC AL, 74H ADC DX, AX ADC AX, [BX] 21-Nov-201014www.eazynotes.com

15 Arithmetic Instructions SUB Des, Src: It subtracts a byte from byte or a word from word. It effects AF, CF, OF, PF, SF, ZF flags. For subtraction, CF acts as borrow flag. E.g.: SUB AL, 74H SUB DX, AX SUB AX, [BX] 21-Nov-201015www.eazynotes.com

16 Arithmetic Instructions SBB Des, Src: It subtracts the two operands and also the borrow from the result. It effects AF, CF, OF, PF, SF, ZF flags. E.g.: SBB AL, 74H SBB DX, AX SBB AX, [BX] 21-Nov-201016www.eazynotes.com

17 Arithmetic Instructions INC Src: It increments the byte or word by one. The operand can be a register or memory location. It effects AF, OF, PF, SF, ZF flags. CF is not effected. E.g.: INC AX 21-Nov-201017www.eazynotes.com

18 Arithmetic Instructions DEC Src: It decrements the byte or word by one. The operand can be a register or memory location. It effects AF, OF, PF, SF, ZF flags. CF is not effected. E.g.: DEC AX 21-Nov-201018www.eazynotes.com

19 Arithmetic Instructions AAA (ASCII Adjust after Addition): The data entered from the terminal is in ASCII format. In ASCII, 0 – 9 are represented by 30H – 39H. This instruction allows us to add the ASCII codes. This instruction does not have any operand. Other ASCII Instructions: AAS (ASCII Adjust after Subtraction) AAM (ASCII Adjust after Multiplication) AAD (ASCII Adjust Before Division) 21-Nov-201019www.eazynotes.com

20 Arithmetic Instructions DAA (Decimal Adjust after Addition) It is used to make sure that the result of adding two BCD numbers is adjusted to be a correct BCD number. It only works on AL register. DAS (Decimal Adjust after Subtraction) It is used to make sure that the result of subtracting two BCD numbers is adjusted to be a correct BCD number. It only works on AL register. 21-Nov-201020www.eazynotes.com

21 Arithmetic Instructions NEG Src: It creates 2’s complement of a given number. That means, it changes the sign of a number. 21-Nov-201021www.eazynotes.com

22 Arithmetic Instructions CMP Des, Src: It compares two specified bytes or words. The Src and Des can be a constant, register or memory location. Both operands cannot be a memory location at the same time. The comparison is done simply by internally subtracting the source from destination. The value of source and destination does not change, but the flags are modified to indicate the result. 21-Nov-201022www.eazynotes.com

23 Arithmetic Instructions MUL Src: It is an unsigned multiplication instruction. It multiplies two bytes to produce a word or two words to produce a double word. AX = AL * Src DX : AX = AX * Src This instruction assumes one of the operand in AL or AX. Src can be a register or memory location. IMUL Src: It is a signed multiplication instruction. 21-Nov-201023www.eazynotes.com

24 Arithmetic Instructions DIV Src: It is an unsigned division instruction. It divides word by byte or double word by word. The operand is stored in AX, divisor is Src and the result is stored as: AH = remainderAL = quotient IDIV Src: It is a signed division instruction. 21-Nov-201024www.eazynotes.com

25 Arithmetic Instructions CBW (Convert Byte to Word): This instruction converts byte in AL to word in AX. The conversion is done by extending the sign bit of AL throughout AH. CWD (Convert Word to Double Word): This instruction converts word in AX to double word in DX : AX. The conversion is done by extending the sign bit of AX throughout DX. 21-Nov-201025www.eazynotes.com

26 Bit Manipulation Instructions These instructions are used at the bit level. These instructions can be used for: Testing a zero bit Set or reset a bit Shift bits across registers 21-Nov-201026www.eazynotes.com

27 Bit Manipulation Instructions NOT Src: It complements each bit of Src to produce 1’s complement of the specified operand. The operand can be a register or memory location. 21-Nov-201027www.eazynotes.com

28 Bit Manipulation Instructions AND Des, Src: It performs AND operation of Des and Src. Src can be immediate number, register or memory location. Des can be register or memory location. Both operands cannot be memory locations at the same time. CF and OF become zero after the operation. PF, SF and ZF are updated. 21-Nov-201028www.eazynotes.com

29 Bit Manipulation Instructions OR Des, Src: It performs OR operation of Des and Src. Src can be immediate number, register or memory location. Des can be register or memory location. Both operands cannot be memory locations at the same time. CF and OF become zero after the operation. PF, SF and ZF are updated. 21-Nov-201029www.eazynotes.com

30 Bit Manipulation Instructions XOR Des, Src: It performs XOR operation of Des and Src. Src can be immediate number, register or memory location. Des can be register or memory location. Both operands cannot be memory locations at the same time. CF and OF become zero after the operation. PF, SF and ZF are updated. 21-Nov-201030www.eazynotes.com

31 Bit Manipulation Instructions SHL Des, Count: It shift bits of byte or word left, by count. It puts zero(s) in LSBs. MSB is shifted into carry flag. If the number of bits desired to be shifted is 1, then the immediate number 1 can be written in Count. However, if the number of bits to be shifted is more than 1, then the count is put in CL register. 21-Nov-201031www.eazynotes.com

32 Bit Manipulation Instructions SHR Des, Count: It shift bits of byte or word right, by count. It puts zero(s) in MSBs. LSB is shifted into carry flag. If the number of bits desired to be shifted is 1, then the immediate number 1 can be written in Count. However, if the number of bits to be shifted is more than 1, then the count is put in CL register. 21-Nov-201032www.eazynotes.com

33 Bit Manipulation Instructions ROL Des, Count: It rotates bits of byte or word left, by count. MSB is transferred to LSB and also to CF. If the number of bits desired to be shifted is 1, then the immediate number 1 can be written in Count. However, if the number of bits to be shifted is more than 1, then the count is put in CL register. 21-Nov-201033www.eazynotes.com

34 Bit Manipulation Instructions ROR Des, Count: It rotates bits of byte or word right, by count. LSB is transferred to MSB and also to CF. If the number of bits desired to be shifted is 1, then the immediate number 1 can be written in Count. However, if the number of bits to be shifted is more than 1, then the count is put in CL register. 21-Nov-201034www.eazynotes.com

35 Program Execution Transfer Instructions These instructions cause change in the sequence of the execution of instruction. This change can be through a condition or sometimes unconditional. The conditions are represented by flags. 21-Nov-201035www.eazynotes.com

36 Program Execution Transfer Instructions CALL Des: This instruction is used to call a subroutine or function or procedure. The address of next instruction after CALL is saved onto stack. RET: It returns the control from procedure to calling program. Every CALL instruction should have a RET. 21-Nov-201036www.eazynotes.com

37 Program Execution Transfer Instructions JMP Des: This instruction is used for unconditional jump from one place to another. Jxx Des (Conditional Jump): All the conditional jumps follow some conditional statements or any instruction that affects the flag. 21-Nov-201037www.eazynotes.com

38 Conditional Jump Table MnemonicMeaningJump Condition JAJump if AboveCF = 0 and ZF = 0 JAEJump if Above or EqualCF = 0 JBJump if BelowCF = 1 JBEJump if Below or EqualCF = 1 or ZF = 1 JCJump if CarryCF = 1 JEJump if EqualZF = 1 JNCJump if Not CarryCF = 0 JNEJump if Not EqualZF = 0 JNZJump if Not ZeroZF = 0 JPEJump if Parity EvenPF = 1 JPOJump if Parity OddPF = 0 JZJump if ZeroZF = 1 21-Nov-201038www.eazynotes.com

39 Program Execution Transfer Instructions Loop Des: This is a looping instruction. The number of times looping is required is placed in the CX register. With each iteration, the contents of CX are decremented. ZF is checked whether to loop again or not. 21-Nov-201039www.eazynotes.com

40 String Instructions String in assembly language is just a sequentially stored bytes or words. There are very strong set of string instructions in 8086. By using these string instructions, the size of the program is considerably reduced. 21-Nov-201040www.eazynotes.com

41 String Instructions CMPS Des, Src: It compares the string bytes or words. SCAS String: It scans a string. It compares the String with byte in AL or with word in AX. 21-Nov-201041www.eazynotes.com

42 String Instructions MOVS / MOVSB / MOVSW: It causes moving of byte or word from one string to another. In this instruction, the source string is in Data Segment and destination string is in Extra Segment. SI and DI store the offset values for source and destination index. 21-Nov-201042www.eazynotes.com

43 String Instructions REP (Repeat): This is an instruction prefix. It causes the repetition of the instruction until CX becomes zero. E.g.: REP MOVSB STR1, STR2 It copies byte by byte contents. REP repeats the operation MOVSB until CX becomes zero. 21-Nov-201043www.eazynotes.com

44 Processor Control Instructions These instructions control the processor itself. 8086 allows to control certain control flags that: causes the processing in a certain direction processor synchronization if more than one microprocessor attached. 21-Nov-201044www.eazynotes.com

45 Processor Control Instructions STC: It sets the carry flag to 1. CLC: It clears the carry flag to 0. CMC: It complements the carry flag. 21-Nov-201045www.eazynotes.com

46 Processor Control Instructions STD: It sets the direction flag to 1. If it is set, string bytes are accessed from higher memory address to lower memory address. CLD: It clears the direction flag to 0. If it is reset, the string bytes are accessed from lower memory address to higher memory address. 21-Nov-201046www.eazynotes.com

47 4717-May-15www.eazynotes.com